Amp Editor V1.4.0-2 for Win 10/8.1/7 (Previous version)
Important Notice
- This version supports Windows 10/8.1/7.
- Since this software was not designed to be operated via a touch panel in Windows 10/8.1, we cannot guarantee operation via a touch panel.
- Use the Editor with the supported firmware listed in the following table.
- If you have already installed an older version of Amp Editor, please un-install it first and then install the new version.
- Amp Editor V1.4.0 supports XMV firmware V1.12 or later. If you are using an XMV unit that has firmware V1.11 or earlier, you must use MTX Editor to update the firmware to V1.12 or later.
- Please do not use the EEE function (*) of network switches in a Dante network. Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts. Therefore we strongly recommend that:
-
1. If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
2. If you use unmanaged switches, make sure to not use network switches that support the EEE function, since EEE operation cannot be disabled in these switches.
* EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.
Version Information
This zip file includes the following software:
- Amp Editor V1.4.0
- XMV Firmware V3.11
- TXn Firmware V1.30
- ACD1 Firmware V1.13
- Dante Firmware (for XMV-D) 3.8.0.24 - 3.5.1.8 - 1.2.8
- Dante Firmware Update Manager V3.10.1.2
Caution after updating
When using Dante Firmware of a version earlier than V3.8.0.24 - 3.5.1.8 - 1.2.2, and Dante Latency is set to less than 1 msec, if the Dante Firmware is updated, the sound may be distorted.
Please carry out one of the following after updating Dante Firmware.
- Initialize the devices.
- Perform [Clear Config] in the "Device Config" tab of the "Device View" window of Dante Controller.
- Reset after changing [Latency] into another value once from the "Device Config" tab of the "Device View" window of Dante Controller.
Amp Editor/XMV Firmware/TXn Firmware/ACD1 Firmware Compatibility
Main Revisions and Enhancements
New Features, Improvements
Amp Editor V1.4.0
- XMV firmware V3.1 is now supported. XMV V3.1 new features such as Input Source Select and Input Redundancy can newly be configured with XMV Device Properties window. The XMV firmware is included in the downloaded zip file.
XMV V3.11
- The limiter parameter for protecting the amplifier has been improved and adjusted to enhance hardware performance.
XMV V3.10
- Added a function in which the input source could be set as digital or analog for each channel independently.
- Added the following redundancy functions.
- Backup mode: Switches to analog input when the pilot tone of the digital input is interrupted due to a broken connection or other problem.
- Override mode: Switches the digital input to a specified analog input when analog audio is detected.
Fixed Bugs
Amp Editor
- None
XMV
- None
Known issue
- If the power of the network switch located between the computer and the XMV is repeatedly restarted, there are rare occasions in which the XMV can no longer be recognized from Amp Editor. If this occurs, the XMV must be restarted.
NOTICE
- It is not possible for an XMV unit assigned to a MTX system to be monitored/controlled from Amp Editor. After an XMV unit has been used within the MTX system, that XMV unit must be initialized if you want to monitor/control it from Amp Editor.
- Amp Editor V1.3.3 or earlier is missing the function that allows selection of the input source of an XMV per channel. In the case synchronizing a file which was made using Amp Editor V1.3.3 or earlier with XMV V3.10 or later, the input source setting will be initialized.
System Requirements
OS | Windows 10 (64 or 32 bit) | Windows 8.1 (64 or 32 bit) | Windows 7 (64 or 32 bit) |
---|---|---|---|
CPU | 32bit: 2GHz or higher Intel Core/Pentium/Celeron family processor;
64bit: Intel 64 compatible processor |
||
Memory | 32bit: 1GB or more;
64bit: 2GB or more |
||
HDD | 300 MB or more | ||
Display | 1024 x 768 pixels or higher; High Color 16-bit or higher | ||
Other | Ethernet (1000BASE-T(*)/100Base-TX/10Base-T) port |
* We recommend 1000BASE-T or higher if you will be connecting Dante devices including the XMV4140-D/XMV4280-D/XMV8140-D/XMV8280-D.
License Agreement and Download File
ATTENTION
PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("AGREEMENT") CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA CORPORATION ("YAMAHA").
BY DOWNLOADING OR INSTALLING THIS SOFTWARE OR OTHERWISE RENDERING IT AVAILABLE FOR YOUR USE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. IF YOU DO NOT AGREE WITH THE TERMS, DO NOT DOWNLOAD, INSTALL, COPY, OR OTHERWISE USE THIS SOFTWARE. IF YOU HAVE DOWNLOADED OR INSTALLED THE SOFTWARE AND DO NOT AGREE TO THE TERMS, PROMPTLY DELETE THE SOFTWARE.
GRANT OF LICENSE AND COPYRIGHT
Yamaha hereby grants you the right to use the programs and data files composing the software accompanying this Agreement, and any programs and files for upgrading such software that may be distributed to you in the future with terms and conditions attached (collectively, “SOFTWARE”), only on a computer, musical instrument or equipment item that you yourself own or manage. While ownership of the storage media in which the SOFTWARE is stored rests with you, the SOFTWARE itself is owned by Yamaha and/or Yamaha’s licensor(s), and is protected by relevant copyright laws and all applicable treaty provisions.
RESTRICTIONS
- You may not engage in reverse engineering, disassembly, decompilation or otherwise deriving a source code form of the SOFTWARE by any method whatsoever.
- You may not reproduce, modify, change, rent, lease, or distribute the SOFTWARE in whole or in part, or create derivative works of the SOFTWARE.
- You may not electronically transmit the SOFTWARE from one computer to another or share the SOFTWARE in a network with other computers.
- You may not use the SOFTWARE to distribute illegal data or data that violates public policy.
- You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation.
Copyrighted data, including but not limited to MIDI data for songs, obtained by means of the SOFTWARE, are subject to the following restrictions which you must observe.
- Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner.
- Data received by means of the SOFTWARE may not be duplicated, transferred, or distributed, or played back or performed for listeners in public without permission of the copyright owner.
- The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified without permission of the copyright owner.
TERMINATION
If any copyright law or provisions of this Agreement is violated, the Agreement shall terminate automatically and immediately without notice from Yamaha. Upon such termination, you must immediately destroy the licensed SOFTWARE, any accompanying written documents and all copies thereof.
DOWNLOADED SOFTWARE
If you believe that the downloading process was faulty, you may contact Yamaha, and Yamaha shall permit you to re-download the SOFTWARE, provided that you first destroy any copies or partial copies of the SOFTWARE that you obtained through your previous download attempt. This permission to re-download shall not limit in any manner the disclaimer of warranty set forth in Section 5 below.
DISCLAIMER OF WARRANTY ON SOFTWARE
You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE and related documentation are provided "AS IS" and without warranty of any kind. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE, EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. SPECIFICALLY, BUT WITHOUT LIMITING THE FOREGOING, YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED.
LIMITATION OF LIABILITY
YAMAHA’S ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. IN NO EVENT SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THE SOFTWARE, EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. In no event shall Yamaha's total liability to you for all damages, losses and causes of action (whether in contract, tort or otherwise) exceed the amount paid for the SOFTWARE.
THIRD PARTY SOFTWARE
Third party software and data ("THIRD PARTY SOFTWARE") may be attached to the SOFTWARE. If, in the written materials or the electronic data accompanying the Software, Yamaha identifies any software and data as THIRD PARTY SOFTWARE, you acknowledge and agree that you must abide by the provisions of any Agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE. Yamaha is not responsible in any way for the THIRD PARTY SOFTWARE or your use thereof.
- Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE. IN ADDITION, YAMAHA EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, as to the THIRD PARTY SOFTWARE.
- Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE.
- Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or consequential damages, expenses, lost profits, lost data or other damages arising out of the use, misuse or inability to use the THIRD PARTY SOFTWARE.
U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE:
The Software is a "commercial item," as that term is defined at 48 C.F.R. 2.101 (Oct 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.72024 (June 1995), all U.S. Government End Users shall acquire the Software with only those rights set forth herein
GENERAL
This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws. Any dispute or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction finds any portion of this Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect.
COMPLETE AGREEMENT
This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha.
Previous versions
Amp Editor
- Previous versions information
- Amp Editor V1.4.0-2 for Win
- Amp Editor V1.4.0 for Win
- Amp Editor V1.3.3 for Win
- Amp Editor V1.3.2-2 for Win
- Amp Editor V1.3.2 for Win
- Amp Editor V1.3.1 for Win
- Amp Editor V1.3.0 for Win
- Amp Editor V1.2.1 for Win
- Amp Editor V1.2.0 for Win
- Amp Editor V1.1.0 for Win
- Amp Editor V1.0.0 for Win